| Ignition order |
1-3-4-2 |
|
|
| Order of numbering of cylinders |
1-2-3-4 |
| Direction of rotation of a bent shaft |
Counterclockwise |
| Ø cylinders, mm |
86.11 |
| Course of pistons, mm |
97.03 |
| Working volume, cm of 3 (l) |
2261 (2.3) |
| Extreme admissible size of not planeness of the inlet pipeline / final collector, mm |
0.152 |
| On a cover of the distributor the plug of connection of VV of a wire of a spark plug of the first cylinder is darkened. |
|
Camshaft
|
| Axial side play, mm |
| Nominal rate |
0.051 ÷ 0.152 |
| Extreme admissible value |
0.508 |
| Maximum admissible size of a side beating, mm |
0.051 |
| Gaps in bearings, mm |
| Nominal rate |
0,051 ÷ 0.089 |
| Extreme admissible value |
0.152 |
| Height of working ledges of cams, mm |
| VTEC models |
| Cams of inlet valves |
| Primary |
37.7749 |
| Average |
39.7256 |
| Secondary |
34.4805 |
| Cams of final valves |
38.3667 |
| Models without VTEC |
| Cams of inlet valves |
38.3388 |
| Cams of final valves |
37.7165 |
|
Oil pump
|
| Gap between teeths of external and internal gear wheels, mm |
| Nominal rate |
0.025 ÷ 0.152 |
| Extreme admissible working value |
0.203 |
| Gap between an external gear wheel and a pump housing, mm |
| Nominal rate |
0.102 ÷ 0.178 |
| Extreme admissible working value |
0.203 |
| Axial gap between a casing of the pump and gear wheels, mm |
| Nominal rate |
0.025 ÷ 0.076 |
| Extreme admissible working value |
0.127 |
|
Efforts of tightening of threaded connections
|
N • m
|
| Bolts of fastening of the delivery camera of an air path |
22 |
| Bolts of fastening of covers of bearings of the camshaft |
| 6.0 x 1.0 mm |
12.2 |
| 8.0 x 1.25 mm |
22 |
| Bolts of a cover of a head of cylinders |
9,7 |
| Nut of fastening of a balancing shaft / натяжителя gas-distributing belt |
45 |
| Camshaft cogwheel bolt |
58 |
| Bolt of a pulley of a bent shaft |
245 |
| Bolts of a head of cylinders |
| Stage 1 |
30 |
| Stage 2 |
To hold on for 90 ° |
| Stage 3 |
To hold on for 90 ° |
| Stage 4 (only for new bolts) |
To hold on for 90 ° |
| Bolts of fastening of a flywheel to a bent shaft |
62 |
| Bolts of fastening of a driving disk to a bent shaft |
73 |
| Nuts of fastening of the inlet pipeline |
22 |
| Nuts of fastening of a final collector |
31 |
| Bolt of fastening of a cogwheel of a forward balancing shaft |
30 |
| Bolt of fastening of a cogwheel of a back balancing shaft |
24 |
| Bolts of fastening of the pallet of a case to the engine block |
13.6 |
| Stopper of the reducing valve |
39 |
| Bolts/nut of fastening of a maslozaborny tube of the oil pump |
11.8 |
| Bolts of a casing of the oil pump |
11.8 |
| Bolts of a casing of a back epiploon of a bent shaft |
11.8 |
| Bolts of fastening of the top and lower covers of a gas-distributing belt |
11.8 |
| Bolts of fastening of the water pump |
See the Head of the Cooling system, heating
|
| Forward support of a suspension bracket of the power unit |
| Bolts of fastening of an arm of a support to the chassis |
38 |
| Bolts of fastening of an arm of a support to the engine |
38 |
| Through bolt |
64 |
| Back support of a suspension bracket of the power unit |
| Bolts of fastening of a pillow of a support to the chassis |
38 |
| Bolts of fastening of an arm of a support to the engine |
54 |
| Support hairpin nut |
54 |
| Left support of a suspension bracket of the power unit |
| Bolts/nuts of fastening of an arm of a support to the engine |
54 |
| Bolts of fastening of a pillow of a support to the chassis |
38 |
| Right support of a suspension bracket of the power unit |
| Through bolt |
40 |
| Nuts of fastening of an arm of a support to transmission |
38 |
| Bolts of fastening of a pillow of a support to the chassis |
38 |
|
V6 engines
|
|
General parameters
|
|
|
Numbering of cylinders (from a gas-distributing belt to transmission) |
| Back row (from a back partition of a compartment) |
1-2-3 |
| A forward row (from a radiator) |
4-5-6 |
| Direction of rotation of a bent shaft |
Clockwise |