Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
- Brake system
System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
Replacement of brake shoes of disk brake mechanisms
Removal and installation of supports of disk brake mechanisms
Check of a state, removal and installation of a brake disk
Replacement of boots of drum brake mechanisms of back wheels
Removal and installation of wheel cylinders
Removal and installation of the main brake cylinder
Check of a state and replacement of brake lines and hoses
Pumping of the brake system
Check of serviceability of functioning/tightness, removal and installation of assembly of the vacuum amplifier of brakes
Adjustment of the parking brake
Replacement of a cable(s) of the drive of the parking brake
Check of serviceability of functioning, replacement and adjustment of the sensor switch of stoplights
Check of serviceability of functioning and replacement of the sensor switch of level of brake fluid
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment
|
Check of a state, removal and installation of a brake disk
|
|
The procedure is equally applicable to disk brake mechanisms of both forward, and back wheels. |
Check of a state
|
|
|
1. Weaken fastening nuts to Coca, a poddomkratta the car and establish it on props. Remove the corresponding wheel, then screw couple of wheel nuts back on fixing hairpins, having enclosed under them washers 3 mm thick for the purpose of fixing of a brake disk (if two screws of fastening of a disk are not turned out yet, need for a navorachivaniye of nuts disappears). When checking a disk of the back brake mechanism do not forget to release the parking brake.
2. Remove a brake support (see the Section Removal and installation of supports of disk brake mechanisms) and tie up it aside a wire to a suspension bracket element, without disconnecting a brake hose.
|
|
3. Make visual check of a condition of a working surface of a disk. Easy defects can be eliminated by means of a fine-grained emery paper. For removal of furrows more than 0.38 mm in depth the disk should be subjected to a pro-point. Remember that the disk has to be examined from both of its parties. |
|
|
4. If during braking pedal pulsations were noticed, it is necessary to estimate the size of a side beating of a brake disk. Fix the dial measuring instrument of plunger type (DTI) at distance about 12.7 mm from the outer edge of a disk. |
|
|
5. Nullify the device and begin to rotate a disk. The result of measurement should not exceed the limit of the admissible range stipulated in Specifications, otherwise the disk needs to be given to a pro-point.
|
|
Authors of the present manual recommend to make a pro-point of disks regardless of their state for the purpose of removal from any working surfaces of defects. As a last resort it is possible to be limited to processing of a disk a fine-grained emery paper. |
|
|
|
6. At a pro-point of a disk it is necessary to pay special attention to observance of requirements of Specifications to its minimum admissible thickness. On a face surface of a disk the corresponding marking is provided. |
|
|
7. Measurement of thickness of a disk is performed by means of a micrometer. |
|
|
REMOVAL
|
|
|
|
1. Turn out two bolts of fastening of an anchor bracket of a support to a rotary fist, |
|
|
2. or (on the brake mechanism of a back wheel) bolts of fastening of a bracket to stupichny assembly. Remove a bracket. |
|
|
3. Remove two wheel nuts used for fixing of a disk on a nave / turn out two fixing screws. Remove a disk from a wheel nave. |
|
|
4. If the disk "stuck" to a nave, it can be squeezed out by a vvorachivaniye in fixing openings of couple of bolts of the suitable size. Tighten bolts evenly and gradually until the disk completely is not released. At removal of a disk try not to damage a carving of hairpins of fastening of a wheel. |
|
|
INSTALLATION
|
|
|
1. Accurately put on a disk a nave (again try not to damage wheel hairpins). Screw and strongly tighten fixing screws.
2. Install an anchor bracket of a support on a drive. Tighten bolts of fastening of a bracket and a support with the required effort.
3. Establish into place a wheel, lower the car on the earth and tighten wheel nuts with the required effort (see Specifications to the Head Nastroyki and routine maintenance). Several times squeeze out a brake pedal / cock the lever of the parking brake for the purpose of shrinkage of blocks on a disk. If brake hoses were not disconnected, need for a prokachivaniye of hydraulic system is absent. Before starting operation of the car, make sure of serviceability of functioning of brakes. |
|
|
|
