Honda Accord

of release

Repair and operation of the car

Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
- Brake system
   System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement of brake shoes of disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Check of a state, removal and installation of a brake disk
   Replacement of boots of drum brake mechanisms of back wheels
   Removal and installation of wheel cylinders
   Removal and installation of the main brake cylinder
   Check of a state and replacement of brake lines and hoses
   Pumping of the brake system
   Check of serviceability of functioning/tightness, removal and installation of assembly of the vacuum amplifier of brakes
   Adjustment of the parking brake
   Replacement of a cable(s) of the drive of the parking brake
   Check of serviceability of functioning, replacement and adjustment of the sensor switch of stoplights
   Check of serviceability of functioning and replacement of the sensor switch of level of brake fluid
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment

Lada Granta 2190 - про автомобиль Lada Granta 2190

Replacement of boots of drum brake mechanisms of back wheels

Assembly of the drum brake mechanism of the right back wheel

1 — the Lever of the automatic regulator
2 — Assembly of the regulator
3 — the Wheel cylinder
4 — the Top coupling spring
5 — the Directing spring

6 — Pruzhina of the automatic regulator
7 — the Lower coupling spring
8 — the Cable of the drive of the parking brake
9 — the Executive lever of the drive of the parking brake

Replacement of boots has to be made at the same time on both brake mechanisms. See also prevention at the beginning of the Section Removal and installation of supports of disk brake mechanisms!

Along with replacement of brake boots also replacement of their coupling and directing springs which as a result of constant cyclic mechanical and thermal loadings stretch/sink over time has to be made, stopping developing the required effort that conducts to a prikhvatyvaniye of brakes and acceleration of wear of drums.


1. Weaken nuts of fastening of back wheels. A car back also establish to Poddomkratta it on props. Prop up forward wheels antiretractable boots. Remove back wheels and release the parking brake.

2. Remove the brake drum from a nave. The drum has to be removed rather freely, in case of difficulties, accurately tap it the hammer with soft brisk, or screw couple of bolts of M8 in carving openings. If the drum still does not give in to removal, it is necessary to wring out brake boots from its working surface. Take a rubber cap from a brake board, pass the screw-driver throughout the opened opening and take away it the self-regulator lever from an adjusting asterisk. The second screw-driver rotate an asterisk until the drum completely is not released.

3. It is simpler to make replacement of boots after removal of stupichny assembly from an axis pin (uncover the wheel bearing, give a shpindelny nut and remove a washer (see the Head Podvesk and steering).

4. Working according to the instructions stated on illustrations make check of a condition of components and replace brake boots. Act strictly in the stipulated order. Remember that all four boots of both brake mechanisms have to be replaced at the same time.

5. Before installation of the reel it is necessary to check it for existence of zadir, furrows, traces of an overheat and other defects. At identification of serious damages which traces cannot be eliminated by processing of a drum with a fine-grained emery paper the drum should be given to a pro-point (with observance of the maximum admissible repair diameter).

Authors of the present manual recommend to make a pro-point of drums regardless of their state for the purpose of any removal of defects and elimination of ovality. If the pro-point of a drum cannot be made without violation of requirements to the maximum admissible internal diameter (it is beaten out on a drum, it is necessary to make its replacement. If it is not possible to make a pro-point of drums, at least, carefully smooth out them working surfaces a fine-grained emery paper.

6. Establish into place assembly of a nave with the wheel bearing, put on a washer and screw a new shpindelny nut, having tightened it with the required effort (see Specifications to the Head Podvesk and steering).
7. Install into place the reel. Pass the screw-driver throughout an opening in a brake board and, rotating a regulator asterisk, press boots to the working surfaces of the reel, then return back an asterisk a little so that the drum began to be rotated freely (preliminary adjustment).
8. Establish into place a wheel, then lower the car on the earth and tighten wheel nuts with the required effort (see Specifications to the Head Nastroyki and routine maintenance).
9. Several times slow down the car at the movement it both to lobbies, and a backing for the purpose of carrying out automatic adjustment of brake mechanisms.
10. Before starting operation of the car, make sure of serviceability of functioning of brakes.