Honda Accord

of release

Repair and operation of the car


Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   + V6 engines
   - General and capital repairs of the engine
      Check of pressure of oil
      Check of compression pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal of the power unit from the car - preparation and precautionary measures
      Removal and installation of the engine
      Alternative versions of schemes of recovery repair of the engine
      Order of dismantling of the engine by preparation it to capital repairs
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal and check of a condition of balancing shaft (4-cylinder engines)
      Removal of conrod and piston assemblies
      Removal of a bent shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of conrod and piston group
      Check of a condition of a bent shaft
      Check of a state and selection of inserts of radical and conrod bearings of a bent shaft
      Engine assembly order
      Installation of piston rings
      Installation of a bent shaft and check of working gaps of radical bearings
      Installation of a back epiploon of a bent shaft
      Installation of conrod and piston assemblies and check of size of working gaps in conrod bearings of a bent shaft
      Installation of balancing shaft (four-cylinder engines)
      Trial start and running in of the engine after capital repairs
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


Removal and check of a condition of balancing shaft (4-cylinder engines)

REMOVAL

 PERFORMANCE ORDER

1. Pass a long bolt 6 x 100 mm (or the long screw-driver of suitable diameter) in a special opening in a pin of a forward balancing shaft and, holding by means of it a shaft from a provorachivaniye, give a bolt of fastening of a cogwheel.

2. Remove a casing of a gear wheel of a back balancing shaft.
3. For blocking of a back balancing shaft pass a bolt or the screw-driver throughout an access opening (previously take a stopper) in a back wall of the block of cylinders. Otboltite casing of a gear wheel of a back shaft. Now to an otboltita also remove a gear wheel of its drive from a shaft.

Put on a bolt a tag at distance of 74 mm from a face cut. The bolt should not be entered into the block more deeply than to this tag.

4. Remove a casing of the oil pump.

5. Turn out two fixing bolts and remove a persistent plate of a forward balancing shaft. Accurately take shaft from the block, - try not to damage bearing surfaces.

CHECK

 PERFORMANCE ORDER

1. Carefully wipe shaft and attentively examine their necks on existence of zadir, scratches, signs of excessive wear and traces of an overheat. Usually wear of necks is shown in emergence of sites, zapolirovanny to mirror gloss.
2. By means of a micrometer measure diameters of forward and back edges of each of necks. The difference between results of measurements corresponds to the size of the conicity taking place. If conicity exceeds value, admissible on spices, the shaft is subject to replacement.
3. Serially lay each of shaft a shaft in V-shaped blocks and fix in a perpendicular axis of a shaft of the plane the dial measuring instrument (DTI) so that its plunger concerned the surface of an average neck. Rotating a shaft in blocks determine the size of its beating. Compare results of measurements to requirements of Specifications, excessively curved shaft are subject to replacement.
4. Measure diameters of necks of a shaft, and also internal diameters of the corresponding bearings. Determine by way of subtraction of results of the first measurements from results of the second the size of a gap of landing of a shaft in bearings. Compare results of measurements to requirements of Specifications. If results of measurements exceed the limit of admissible range, and shaft are in satisfactory condition, deliver the block a workshop of car service for the purpose of performance of replacement of bearings.