Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
- Engine
   + Four-cylinder engines
   + V6 engines
   - General and capital repairs of the engine
      Check of pressure of oil
      Check of compression pressure in cylinders
      Diagnostics of a condition of the engine with use of the vacuum gage
      Removal of the power unit from the car - preparation and precautionary measures
      Removal and installation of the engine
      Alternative versions of schemes of recovery repair of the engine
      Order of dismantling of the engine by preparation it to capital repairs
      Dismantling of a head of cylinders
      Cleaning and check of a condition of a head of cylinders
      Service of valves
      Assembly of a head of cylinders
      Removal and check of a condition of balancing shaft (4-cylinder engines)
      Removal of conrod and piston assemblies
      Removal of a bent shaft
      Cleaning of the block of the engine
      Check of a condition of the block of the engine
      Honingovaniye of mirrors of cylinders
      Check of a condition of components of conrod and piston group
      Check of a condition of a bent shaft
      Check of a state and selection of inserts of radical and conrod bearings of a bent shaft
      Engine assembly order
      Installation of piston rings
      Installation of a bent shaft and check of working gaps of radical bearings
      Installation of a back epiploon of a bent shaft
      Installation of conrod and piston assemblies and check of size of working gaps in conrod bearings of a bent shaft
      Installation of balancing shaft (four-cylinder engines)
      Trial start and running in of the engine after capital repairs
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


Lancia Musa - про автомобиль Lancia Musa

Removal of a bent shaft

Removal of a bent shaft is possible only from the engine taken from the car. It is meant that a flywheel / a driving disk, the gas-distributing belt, the case pallet, a maslozabornik, the oil pump and conrod and piston assemblies are already dismantled. On 4-cylinder engines dismantle of the connecting bridge has to be made before removal of rods (see the Section Removal of Conrod and Piston Assemblies). Before removal of a bent shaft it is also necessary to otboltit and separate from the block of cylinders the holder of a back epiploon.


 PERFORMANCE ORDER

1. Before starting extraction of a bent shaft from the engine, measure the size of its axial side play. Fix the DTI measuring instrument on the block to coaxially bent shaft, having rested its plunger against a cheek of one of cranks.

Covers of radical bearings and their connecting bridge (4-cylinder engines) have to remain on the places, and their fixture is tightened with the required effort.

2. Push a bent shaft against the stop back and nullify the device indicator. Now push a shaft in an opposite direction and consider the indication of the measuring instrument. The size of a free wheeling of a shaft in the longitudinal direction is also its axial side play. Compare result of measurement to requirements of Specifications. If the side play exceeds the maximum admissible value, check persistent surfaces of a shaft for existence of signs of excessive wear. In the absence of obvious signs of wear, installation of new persistent washers usually helps to correct a situation.

3. In the absence of near at hand dial measuring instrument it is possible to use the ordinary probe of lezviyny type. Accurately shift a shaft against the stop forward on the engine, then determine the size of the formed gap between a cheek of a crank and a back wall of the persistent (forward) radical bearing, having densely put in it the corresponding thickness a probe edge(s).

4. Check covers of radical bearings for existence on them adjusting marking. Covers have to be numbered consistently in the direction in front back on the engine. In case of need put marking independently by means of a center punch. Besides serial number on covers marking in the form of cast arrows is usually provided. On correctly established covers of the shooter has to specify in the direction of a belt of the GRM drive.

5. On 4-cylinder engines in stages (on 1/4 turns for approach) weaken bolts of fastening of covers of radical bearings / their connecting bridge so that the possibility of their reversing manually appeared. Remove the bridge. The hammer with soft brisk carefully tap covers of bearings and separate them from the block, in case of need use bolts as levers. Try not to drop inserts of radical bearings.

6. On V6 engines the cover of each of radical bearings fastens four bolts, - two bolts are rolled in the vertical plane (looking at the block from below) and two more are screwed from each of the parties in the horizontal plane. Before making attempts of separation of covers from the block, make sure that all bolts are turned out.

7. Carefully take a bent shaft from the engine (use the help of the assistant). Track that inserts of radical bearings remained in the beds in the block and covers. Install covers on the block, then by hand tighten bolts of their fastening.