Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Start of the engine from the auxiliary power supply
   Check of a state and replacement of the battery
   Check of a state and replacement of wires of the battery
   System of ignition - the general information
   Check of functioning of system of ignition
   Check of a state and replacement of the coil of ignition
   Check of serviceability of functioning and replacement of the module of management of ignition (ICM)
   Removal and installation of the distributor of ignition
   Check of installation of a corner of an advancing of ignition
   System of a charge - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and installation of the generator
   Replacement of the regulator of tension and brushes of the generator
   System of start - the general information and precautionary measures
   Check of serviceability of functioning of a starter on the car (in situ)
   Removal and installation of a starter
   Removal and installation of the traction relay
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment





Check of a state and replacement of the coil of ignition

4-cylinder models

CHECK

 PERFORMANCE ORDER

1. Switch off ignition (the key has to be turned in position of OFF).
2. Remove a cover, the runner and the filter from the distributor.
3. Disunite electric sockets of primary contour of the coil of ignition.
4. By means of an ohmmeter measure resistance between plugs (And yes In) primary winding of the coil. Compare result of measurement to requirements of Specifications.

5. Then measure resistance between the positive plug of primary winding (A) and the plug of a secondary winding. Again compare result to requirements of Specifications.

6. Remember that standard values of resistance of windings change with a temperature. The nominal rates characteristic of temperature of the coil of 21 °C are specified in Specifications.
7. If in any of the last two checks the result of measurement exceeds the limit of admissible range, replace the ignition coil.

REPLACEMENT

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Remove from the distributor a cover and the filter (at the corresponding complete set) (see the Head Nastroyki and routine maintenance). Disconnect wires from plugs of primary contour of the coil.

3. Turn out two fixing screws and take the ignition coil from assembly of the distributor.

4. Installation is made upside-down.

4-cylinder models

CHECK

 PERFORMANCE ORDER

1. Switch off ignition (the key has to be turned in position of OFF).
2. Disconnect VV a wire from the plug of a secondary winding (bobbin).
3. Remove the 3-contact socket from primary plugs of the coil of ignition.

4. By means of an ohmmeter measure resistance between plugs (1 and 3 primary windings of the coil. Compare result of measurement to requirements of Specifications.

5. Connect an ohmmeter between the average plug (2) and the plug of a secondary winding. Compare result of measurement to requirements of Specifications.
6. Remember that standard values of resistance of windings change with a temperature. The nominal rates characteristic of temperature of the coil of 21 °C are specified in Specifications.
7. If in any of the last two checks the result of measurement exceeds the limit of admissible range, replace the ignition coil.

REPLACEMENT

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Disconnect an electrical wiring from the ignition coil.

3. Turn out fixing bolts and remove the ignition coil.

4. Installation is made upside-down.