Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross stability
   Removal and installation of the pushing bar of a forward suspension bracket
   Removal and installation of the lower control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of rack transfer
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Angles of installation of wheels
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment



Removal and installation of stupichny assembly of a back wheel

REMOVAL

 PERFORMANCE ORDER

1. Weaken nuts of fastening of the corresponding back wheel. A car back also establish to Poddomkratta it on props. Remove a wheel.

Models with disk brake mechanisms of back wheels

2. Otboltite from stupichny assembly an arm of fastening of a brake hose. Otboltite a support also tie up it a wire to a screw spring. Remove an anchor bracket of a support (see the Head the Brake system).
3. Turn out two fixing screws and remove a brake disk from stupichny assembly (see the Head the Brake system).

Models with drum brake mechanisms of back wheels

4. Disconnect the brake line from the wheel cylinder (see the Head the Brake system).
5. Remove a drum and assembly of brake boots (see the Head the Brake system).

All models

6. Remove from stupichny assembly a nave with the wheel bearing (see the Section Removal and installation of assembly of a back nave with the wheel bearing).
7. Give a nut of fastening of the top end of the corresponding rack of the stabilizer of cross stability (see the Section Removal and installation of a bar of the back stabilizer of cross stability).
8. Disconnect from stupichny assembly the lower end of the shock-absorber (see the Section Removal and installation of assembly of the back shock-absorber with a screw spring).
9. Otboltite from stupichny assembly suspension bracket levers (see the Section Removal and installation of levers of a back suspension bracket).
10. Remove stupichny assembly from levers.
11. In case of need replacements of the wheel bearing remove from assembly a nave (see the Section Removal and installation of assembly of a back nave with the wheel bearing).

INSTALLATION

 PERFORMANCE ORDER

1. Connect to stupichny assembly suspension bracket levers (see the Section Removal and installation of levers of a back suspension bracket). Tighten fixing nuts with the required effort.
2. Connect the lower end of the shock-absorber to assembly. With the required effort tighten a nut of a fixing bolt.
3. Connect to the arm on stupichny assembly a rack of the stabilizer of cross stability. Tighten a fixing nut with the required effort.
4. Establish on the regular place assembly of a nave with the wheel bearing (see the Section Removal and installation of assembly of a back nave with the wheel bearing).
5. Install components of the brake mechanism (see the Head the Brake system). During the work on model with disk brake mechanisms of back wheels do not forget to pump over the brake system.
6. Establish into place a wheel, lower the car on the earth and tighten wheel nuts with the required effort (see Specifications to the Head Nastroyki and routine maintenance).