Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross stability
   Removal and installation of the pushing bar of a forward suspension bracket
   Removal and installation of the lower control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of rack transfer
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Angles of installation of wheels
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment





Removal and installation of a rotary fist

REMOVAL

 PERFORMANCE ORDER

If the cap of a disk is not fixed by wheel nuts, begin with implementation of the procedure of paragraph 4.

1. Weaken nuts of fastening of a wheel, a front of the car and establish to a poddomkratta it on props.
2. Give wheel nuts and take off a decorative cap from a disk, remove a wheel.
3. By a drift to a raschekanta a washer of a stupichny nut, then establish into place a wheel without cap and lower the car on the earth.

4. By means of a face key with a long collar weaken a stupichny nut.

5. Weaken wheel nuts, a front of the car and establish to a poddomkratta it on props. Remove a wheel and give a stupichny nut.
6. Release a flexible brake hose from an arm on assembly of a rotary fist. Otboltite a support of the brake mechanism also tie up it a wire to a screw spring. Remove also anchor bracket of a support and a brake disk (see the Head the Brake system).
7. Turn out two fixing screws and remove a brake disk from stupichny assembly (see the Head the Brake system).
8. Remove the wheel ABS sensor (see the Head the Brake system).
9. Disconnect from a rotary fist a tip of steering draft (see the Section Removal and installation of tips of steering drafts).
10. Separate the lower lever of a suspension bracket from a spherical support in the lower part of a rotary fist (see the Section Removal and installation of the lower control lever of a forward suspension bracket).
11. Separate the top end of a fist from a spherical support of the top lever of a suspension bracket (see the Section Removal and installation of the top control lever of a forward suspension bracket).

12. Accurately delay assembly of a fist with a nave outside, having removed it from a pin of a power shaft. In case of need knock on a pin end face with the hammer with soft brisk for the purpose of release of the CV JOINT from a nave. Tie up assembly of a power shaft a wire in order to avoid damage of the internal CV JOINT.

13. If there is a need for replacement of the stupichny bearing, deliver assembly of a rotary fist in a workshop of car service.

INSTALLATION

 PERFORMANCE ORDER

1. If made assembly dismantle, establish a nave on a rotary fist (work has to be performed in the conditions of a workshop of car service).
2. Slightly grease with special lubricant of a vent of an external pin of a power shaft. Pass a pin through an opening in a nave, at the same time filling a rotary fist on the regular place.
3. Connect the top part of a fist to a spherical support of the top lever of a suspension bracket (see the Section Removal and installation of the top control lever of a forward suspension bracket). Tighten a nut of a spherical finger with the required effort and record it the new forelock.

Tighten a nut with the minimum admissible effort, then, hold on it to combination of openings under landing of the forelock.

4. Connect a spherical support in the lower part of a fist to the lower lever of a suspension bracket (see the Section Removal and installation of the lower control lever of a forward suspension bracket). Tighten a koronchaty nut with the required effort and record it the new forelock (see the Remark in the previous paragraph).
5. Establish into place a brake disk, having strongly tightened fixing screws.
6. Establish an anchor bracket and a support, having tightened fixture of components with the required effort (see the Head the Brake system). Fix a flexible brake hose in a basic arm on assembly of a rotary fist. Strongly tighten fixing bolts.
7. Screw a stupichny nut on a pin of a power shaft and strongly tighten it.
8. Establish a wheel (if it is necessary - a disk cap), lower the car on the earth and tighten wheel nuts with the required effort (see Specifications to the Head Nastroyki and routine maintenance).
9. Tighten a stupichny nut with the required effort (see Specifications to the Head Stsepleniye and power shafts).