Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross stability
   Removal and installation of the pushing bar of a forward suspension bracket
   Removal and installation of the lower control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of rack transfer
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Angles of installation of wheels
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment



Angles of installation of wheels

 

The angles of installation of forward wheels define geometry of situation of the last concerning a suspension bracket of the car and a paving. Violation of adjustment of this geometry leads to decrease in controllability of the car and increase in speed of wear of tires. The angles of installation of forward wheels of the car which are subject to control are among disorder, выбег (a corner of a longitudinal inclination of an axis of turn of a wheel) and convergence. Only one of parameters - convergence, and, both forward, and back wheels of the car is subject to adjustment. Sizes of disorder and a vybeg of forward wheels have to be checked on a regular basis for assessment of degree of wear of components of a suspension bracket and the steering drive.

Adjustment of angles of installation of wheels is among the procedures demanding the special accuracy of measurement which high-quality implementation requires existence of special, rather bulky and expensive equipment. Performance of this work will be most correct to be charged to professional mechanics of car service. Below, for the general understanding, definitions of each of the under control angles of installation of wheels of the car which knowledge will facilitate communication of the owner of the car with personnel of car service are given.

Convergence is called data size to each other of forward edges of wheels of the car. Such violation of parallelism of installation of wheels allows to minimize wear of a protector at the expense of a skid at commission of turns. At zero convergence the distance between forward edges of wheels is equal to distance between their rear edges. Normal convergence usually does not exceed inch shares (1 inch = 2.54 cm). Adjustment of convergence of forward wheels is carried out by adjustment of length of steering drafts due to change of provision of their tips. For correction of convergence of back wheels the special adjusting cam bolt screwed in the internal end of a control lever of a back suspension bracket is provided. Violation of adjustment of convergence leads to acceleration of wear of protectors of tires due to slipping them on a paving.

Disorder is called the tilt angle of the plane of wheels concerning a vertical. If wheels are inclined by the upper edges outside, disorder is called positive and vice versa. The size of disorder is measured in degrees. Correctness of adjustment of disorder determines the size and the provision of a spot of contact of protectors with the road and allows to compensate changes in suspension bracket geometry during commission of turns and at the movement of the car on an uneven paving. On the considered models of cars the possibility of adjustment of disorder is not provided.

Vybegom is called a deviation corner from a vertical of an axis of turn of a wheel in the plane of the last. If the axis of turn is inclined back, выбег is called positive, on the contrary. Adjustment of a vybeg of forward wheels is carried out by selection of the remote washers enclosed under the pushing suspension bracket bars.