Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assembly of the forward shock-absorber with a screw spring
   Replacement of the shock-absorber or screw spring of rack-mount assembly
   Removal and installation of a rotary fist
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross stability
   Removal and installation of the pushing bar of a forward suspension bracket
   Removal and installation of the lower control lever of a forward suspension bracket
   Removal and installation of the top control lever of a forward suspension bracket
   Replacement of spherical support
   Removal and installation of assembly of the back shock-absorber with a screw spring
   Removal and installation of stupichny assembly of a back wheel
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross stability
   Removal and installation of levers of a back suspension bracket
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of the steering mechanism
   Removal and installation of rack transfer
   Removal and installation of the steering pump
   Removal of air from a hydraulic path of system of strengthening of a wheel
   Wheels and tires - the general information
   Angles of installation of wheels
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


Обзор напольных покрытий - ковролина и плинтуса

Removal and installation of levers of a back suspension bracket

 PERFORMANCE ORDER

Weaken nuts of fastening of the corresponding wheel. A car back also establish to Poddomkratta it on props. Remove a wheel.

Top lever

 PERFORMANCE ORDER

1. Give a nut of a through bolt of fastening of the top lever of a suspension bracket to stupichny assembly. Also remove a nut of a spherical finger of a support of the lever. By means of a 2-gripping stripper separate the lever from stupichny assembly.
2. Turn out bolts of fastening of a basic arm of a brake hose, take the brake line aside.
3. On the models equipped with ABS remove the wheel sensor in order to avoid casual damage of its electrical wiring.

4. Turn out a bolt of fastening of the internal end of the top lever to the chassis.

5. Remove the top lever. Check a condition of rubber plugs of the lever, estimate a weak point of landing and degree of wear of the spherical hinge. Replace the worn-out and damaged components.
6. Installation is made upside-down. Track that all fixture was tightened with the required effort. Do not forget to record a koronchaty nut of a spherical finger the new forelock (see the Remark to paragraph 1 of the Section Removal and installation of a rotary fist).

Lower lever

 PERFORMANCE ORDER

1. Give a nut of a bolt of fastening of the lower lever to stupichny assembly.
2. Turn out an axial bolt of fastening of the internal end of the lower lever to the chassis.

3. Remove assembly of the lower lever.
4. Check a condition of rubber plugs, in case of need replace the lever.
5. Installation is made upside-down. Track that all fixture was tightened with the required effort.

Forward longitudinal lever

 PERFORMANCE ORDER

1. Disconnect a basic arm of a driving cable of the parking brake from the longitudinal lever.
2. Turn out a bolt of fastening of the longitudinal lever to stupichny assembly.
3. Turn out a bolt of fastening of the longitudinal lever to the chassis.

4. Remove the forward longitudinal lever.
5. Check a condition of the plug installed in a forward part of the lever. In case of detection of defects replace the lever.
6. Installation is made upside-down. Track that all fixture was tightened with the required effort.

Longitudinal lever

 PERFORMANCE ORDER

1. Turn out a bolt of fastening of the longitudinal lever to stupichny assembly.
2. Turn out a bolt of fastening of the lever to the chassis.

3. Remove the lever.
4. Check a condition of the plug installed since the internal end of the lever. In case of detection of defects replace the lever.
5. Installation is made upside-down. Track that all fixture was tightened with the required effort.

Control lever

 PERFORMANCE ORDER

1. Give hectare (see an accompanying illustration).
2. Mark the provision of an adjusting cam in relation to a basic arm of the internal end of the lever. Give a nut, and take a bolt of fastening of the lever to the chassis.

3. Remove the lever.
4. Check a condition of rubber plugs of the lever. In case of detection of defects replace the lever.
5. Installation is made upside-down. Track correctness of combination of the landing marking put in the course of dismantle (see paragraph 2). Tighten all fixture with the required effort.