Honda Accord

of release

Repair and operation of the car

Honda Chord
+ Cars of the Honda Accord brand
- Settings and routine maintenance
   General information about settings and adjustments
   Check of levels of liquids
   Check of a condition of tires and pressure of their rating
   Check of level of liquid of the power steering
   Check of the ATF AT level
   Replacement of motive oil and oil filter
   Check of a state and replacement of brushes of screen wipers
   Check, service and charging of the rechargeable battery
   Check of a state, adjustment of effort of a tension and replacement of driving belts
   Check of a state and replacement of the hoses located in a motive compartment
   Check of a condition of components of the cooling system
   Rotation of wheels
   Check of the brake system
   Check of a condition of seat belts
   Replacement of the filtering air cleaner element
   Check of a condition of components of a power supply system
   Check of level of the RKPP gearbox oil
   Survey of components of a suspension bracket and steering drive, check of a condition of protective covers of power shafts
   Check of a condition of components of system of production of the fulfilled gases
   Check of a state and replacement of spark plugs
   Check of a state and replacement of VV of candle wires, cover and runner of the distributor
   Check and replacement of the valve of system of the operated ventilation of a case (PCV)
   Check and adjustment of turns of idling
   Service of the cooling system (depletion, washing and filling)
   Replacement of brake fluid
   Replacement of liquid of automatic transmission (AT/CVT)
   Replacement of the RKPP gearbox oil
   Replacement of filters of the air conditioning system
   Check and adjustment of gaps of valves (as necessary)
   Dropping indicator of intervals of routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment

Check and adjustment of gaps of valves (as necessary)

CHECK

Need for adjustment of valvate gaps arises only after replacement or repair of components of the valvate mechanism.

The simplest way of check of valves is listening of the engine at an open cowl. Indicates the raised noise background published by the valvate mechanism the need of carrying out adjustment.

Check and adjustment of valvate gaps have to be made at the cold engine.

Adjustment

4-cylinder engines

PERFORMANCE ORDER

1. Uncover heads of cylinders and the top cover of a gas-distributing belt (see the Head Dvigatel).
2. Bring the piston of the first cylinder into the provision of VMT of the end of a step of compression for what it is necessary to turn a bent shaft for a pulley so that the tag of "UP" on a cogwheel of the camshaft fell into a state for 12 hours (see the Head Dvigatel).

3. Having brought the engine into the stipulated situation, it is possible to start check and adjustment of valves of the first cylinder. The scheme of an arrangement of valves on the engine is submitted on an illustration.

4. Begin with the inlet valve. Fill an edge of the measuring probe of the required thickness (see Specifications) in a gap between an end face of a core of the valve and a yoke of its drive of the valve. The probe has to slide in a gap with an insignificant resistance. In case of need release a cap key a lock-nut, the screw-driver weaken the adjusting screw, then begin to tighten it, trying to obtain the required effect on a probe edge.

5. Having fixed the adjusting screw the screw-driver from a provorachivaniye, tighten a lock-nut. Make sure that the gap in the course of tightening of a nut did not change, then, working in a similar manner, serially adjust gaps of the second inlet valve and two final.
6. Having turned a bent shaft on 180 ° counterclockwise (the cogwheel of the camshaft has to be turned on 90 °), bring the piston of the third cylinder into the provision of VMT of the end of a step of compression. At the same time UP tag on a cogwheel of the camshaft has to pass into situation for 9 hours. Check and adjust valves of the third cylinder.
7. Turn a bent shaft for 180 ° counterclockwise (the tag of UP will fall down for 6 hours) and adjust valves of the fourth cylinder.
8. Having once again turned a bent shaft on 180 ° (the tag of UP has to pass into situation for 3 hours), repeat the procedure for valves of the second cylinder.
9. Having finished adjustment of valves, establish to the place of a cover of a head of cylinders and a gas-distributing belt.

V6 engines

PERFORMANCE ORDER

1. Remove the top delivery camera of the inlet pipeline, the top cover of a gas-distributing belt of a forward number of cylinders, and also covers of both heads of cylinders (see the Head Dvigatel).

2. Having turned a bent shaft, bring the piston of the first cylinder into the provision of VMT (see the Head Dvigatel). At the same time the corresponding tag on a cogwheel of the camshaft has to be combined with the index on a back cover of the GRM drive.

3. In the stipulated position of the engine make adjustment of valves of the first cylinder.

About 4 valves are provided in each of cylinders (2 inlet and 2 final). The order of implementation of the procedure is similar described above in paragraphs 3 and 4 of the present Section.

4. Having turned a bent shaft for a pulley in the direction clockwise, achieve combination with the index of a tag of VMT of the 4th the cylinder and make adjustment of its valves. Continuing to work in a similar manner (you pass the cylinder to the cylinder as ignition), serially execute adjustment of valves of all remained cylinders.

The bent shaft every time should be turned clockwise.

5. Establish to the place of a cover of heads of cylinders, the top cover of a gas-distributing belt and the top delivery camera of the inlet pipeline.

home