Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
+ Engine management
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of components of a body and bottom of the car
   Care of vinyl elements of finishing
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and locks of the car
   Replacement wind and other fixed glasses
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of overlays of forward and back bumpers
   Removal and installation of forward wings
   Removal, installation and adjustment of a cover of the luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of the luggage compartment
   Driving cables of an otpuskaniye of locks of a cover of the luggage compartment and door of the hatch of a jellied mouth of the fuel tank
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of provision of doors
   Removal and installation of a latch and external handle / cylinder of the lock of a door
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of a forward fairing
   Removal and installation of seats
   Removal and installation of the back shelf
   Geometrical sizes of various options of execution of a body
+ Onboard electric equipment
+ Schemes of electric equipment


Азиатки индивидуалки Владивостока.

Removal and installation of panels of an internal upholstery of doors

For protection of hands against cuts at performing procedures through access openings in a doorframe put on gloves.

REMOVAL

 PERFORMANCE ORDER

1. On models with the manual drive of window regulators remove the glass lowering/lifting handle.

2. Remove the button of switching off of the lock of a door.
3. For dismantle of the internal handle of a door remove a plastic protective cap and turn out the only fixing screw. Release assembly of the handle from the door panel and disconnect from it an executive rod. At the corresponding complete set of the car disconnect a lock activator electrical wiring.

4. Remove a decorative cover of external basic knot of a rear-view mirror.

5. Turn out screws of fastening of the panel of an internal upholstery, and also the screw of fastening of assembly of an armrest, then accurately delay the panel on yourself, releasing fixing clamps. Moving on panel perimeter, serially release all clamps.

Clamps are located rather deeply under edge of the panel to use the standard tool for a poddevaniye of the last.

6. After all clamps are released, disunite all remained electric sockets and remove the panel from a doorframe.

7. For the purpose of ensuring access to the external handle and the regulator of a window regulator located in a doorframe, remove assembly of control of the electric drive (at the corresponding complete set of the car), assembly door a bracket of the panel and assembly of a loudspeaker (see the Head Onboard electric equipment), then accurately separate the plastic moisture filter.

INSTALLATION

 PERFORMANCE ORDER

1. Before installation of the panel of an internal upholstery make sure available on the places and serviceability of a condition of all its clamps.
2. At the corresponding complete set of the car connect an electrical wiring to the activator of the door lock and the control panel of the window regulator electric drive. Install the panel on a door. Reliably latch all provided clamps. Establish into place and fix by the screw assembly of the internal handle. Install the lock switch (if it is provided) / a ware pocket (strongly tighten the fixing screw). Install the handle of the manual drive window regulator/assembly of management of functioning of the electric drive.