Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
- Engine management
   System of onboard diagnostics (OBD) - the principle of functioning and codes of malfunctions
   Removal and PCM/ECM installation
   Check of serviceability of a state and replacement of the sensor of provision of a butterfly valve (TPS)
   Check of serviceability of a state and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of serviceability of a state and replacement of the sensor of temperature of the soaked-up air (IAT)
   Check of serviceability of a state and replacement of the sensor of temperature of cooling liquid of the engine (EST)
   Check of serviceability of a state and replacement of the sensor of VMT/provision of a bent shaft (TDC/ICR)
   Check of serviceability of a state and replacement of the sensor of position of pistons (CYP)
   Check of serviceability of a state and replacement of the detector of control of electric loadings (ELD)
   Check of serviceability of a state and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of serviceability of a state and replacement of the oxygen sensor (l-probe)
   Check of serviceability of a state and replacement of the sensor of a detonation
   Check of serviceability of a state and replacement of the sensor of speed of the movement of the car (VSS)
   Check of serviceability of functioning and replacement of the valve of stabilization of turns of idling (IAC)
   Check of serviceability of functioning and replacement of the air valve of correction of composition of air-fuel mix (FIA)
   System of the operated ventilation of a case (PCV)
   System of recirculation of the fulfilled gases (EGR) - the general information, check of a state and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a state and replacement of components
   The catalytic converter - the general information, check of a state and replacement
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment


Жир

Removal and PCM/ECM installation

The models of cars considered in the present manual are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid getting injured at its casual operation (see the Head Onboard electric equipment). It is easy to distinguish an electrical wiring of a chain of SRS on yellow color of isolation.

In order to avoid damage of RSM by the electrostatic category, try not to touch contact plugs of the module. Whenever possible you make self-grounding. RSM is among components of anticreeping system and provides an engine immobilization. When replacing RSM the new module before start of the engine needs to be programmed in the conditions of a workshop of car service. Performance actually of replacement of RSM, strictly speaking, will be also more correct to be charged to experts.


 PERFORMANCE ORDER

1. The module of management of RSM is in interior of the car under the dashboard, near assembly of the central console.
2. Disconnect SRS (see the Head Onboard electric equipment).

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for introduction of the equipment to action!

3. Turn off a carpet from the lower part of the central console in driver's and passenger foot wells (see the Head Kuzov), easy access to assembly of RSM has to open.

4. Disunite the RSM electric sockets.

In order to avoid damage of the processor ignition at shutdown/connection of an electrical wiring has to be switched off (a key in position of OFF).

5. Turn out bolts of fastening of a basic arm of RSM.

6. Carefully remove RSM.

In order to avoid damage of RSM by static electricity, try not to touch contact plugs of the module. Whenever possible you make self-grounding. Apply special electrostatic laying to storage of the module (ask in shops of automobile accessories).

7. Installation is made upside-down.

When replacing the module it is necessary to enter into it a code of system of an immobilization of the engine in the conditions of a workshop of car service.