Honda Accord

of release

Repair and operation of the car



Honda Chord
+ Cars of the Honda Accord brand
+ Settings and routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Engine electric equipment
- Engine management
   System of onboard diagnostics (OBD) - the principle of functioning and codes of malfunctions
   Removal and PCM/ECM installation
   Check of serviceability of a state and replacement of the sensor of provision of a butterfly valve (TPS)
   Check of serviceability of a state and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of serviceability of a state and replacement of the sensor of temperature of the soaked-up air (IAT)
   Check of serviceability of a state and replacement of the sensor of temperature of cooling liquid of the engine (EST)
   Check of serviceability of a state and replacement of the sensor of VMT/provision of a bent shaft (TDC/ICR)
   Check of serviceability of a state and replacement of the sensor of position of pistons (CYP)
   Check of serviceability of a state and replacement of the detector of control of electric loadings (ELD)
   Check of serviceability of a state and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of serviceability of a state and replacement of the oxygen sensor (l-probe)
   Check of serviceability of a state and replacement of the sensor of a detonation
   Check of serviceability of a state and replacement of the sensor of speed of the movement of the car (VSS)
   Check of serviceability of functioning and replacement of the valve of stabilization of turns of idling (IAC)
   Check of serviceability of functioning and replacement of the air valve of correction of composition of air-fuel mix (FIA)
   System of the operated ventilation of a case (PCV)
   System of recirculation of the fulfilled gases (EGR) - the general information, check of a state and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a state and replacement of components
   The catalytic converter - the general information, check of a state and replacement
+ Gear shifting box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Schemes of electric equipment



Check of serviceability of a state and replacement of the detector of control of electric loadings (ELD)

CHECK

 PERFORMANCE ORDER

1. The ELD system reveals signs of an overload of electric chains of systems of external lighting and alarm fixtures, injection of fuel, a charge, etc. The first symptom of such overloads is violation of stability of giving of food on single turns of the engine. The failure of the detector leads to record in memory of system of self-diagnostics of a code of malfunction of P1297 or P1298.

2. Remove ELD (see below paragraph 1) and disconnect from it an electrical wiring. Measure tension between the plug 1 (+) and weight on the socket from a plait at the included ignition (the engine do not start). The nominal rate equals to battery tension. If tension is absent, check a condition of an electrical wiring on the site between a safety lock No. 6 on 15 A and the detector.

3. At the included ignition (do not start the engine) measure tension between the plug 3 (+) and weight on the socket from a plait. The required value makes 4.5 ÷ 5.0 Century. In the absence of the required result check a condition of an electrical wiring of ELD on the site between the engine and the generator.
4. Make sure available conductivity between the plug No. 2 and weight.
5. In case of negative results of the checks described above replace the ELD block.

REPLACEMENT

 PERFORMANCE ORDER

1. The ELD block is located in the assembly block of safety locks/relay in a motive compartment of the car. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action!

2. Turn out two fixing screws, take the ELD block from the central part of the assembly block and disconnect from it an electrical wiring.

3. Installation is made upside-down.