|
|
Replacement of the broken valvate springs and worn-out maslootrazhatelny caps can be made without dismantle of a head of cylinders. Only two special adaptations and a source of compressed air will be necessary. Before starting performance of work, make sure available near at hand rather powerful tool for tightening of the hard valvate springs used for a complete set of engines of the considered models of cars. |
1. Uncover a head of cylinders (see the Section Removal and installation of a cover of a head of cylinders).
2. Turn out spark plugs from cylinders which components need check. If there is a need for replacement of maslootrazhatelny caps, turn out all candles.
3. Having turned a bent shaft, bring the corresponding piston into the provision of VMT of the end of a step of compression (see the Section Reduction of the Piston of the First Cylinder in the provision of the top dead point (TDP)). When replacing maslootrazhatelny caps, begin with the first cylinder, then you pass from one to another as ignition (see Specifications).
4. Remove assembly of yokes with axes (see the Section Removal, check of a state and installation of assembly of yokes).
|
|
5. Screw a long transitional nozzle in a candle opening of the corresponding cylinder and connect to it a hose from a source of compressed air. Remark: Special carving nozzles with the union of bystry connection are issued - ask in shops of car service. |
6. Give air to the cylinder.
|
|
Under pressure of air the piston can move down that it will lead to a sudden provorachivaniye of a bent shaft - do not leave on the bolt screwed in a shaft pin, a face key by means of which brought the piston into the provision of VMT. Valves will be kept on the place by air pressure. |
|
|
7. In order to avoid hit in the engine of garbage and other foreign objects, a zakuporta rags all openings in the block around the valves which are subject to service. Now by means of the special tool squeeze a spring of the served valve. |
|
|
8. By means of tweezers or the magnetized core take from flutes on a valve core crackers of the cutting lock. |
9. Remove from a valve core a plate springs, the filter, and actually a spring, then remove a maslootrazhatelny cap from the directing plug.
|
|
If it is not possible to fix the valve in a closed position compressed air, therefore, the tightness violation determined by existence of mechanical defects of a working facet of a plate of the valve or its saddle takes place. In that case the head of cylinders needs to be removed from the engine for the purpose of performance of the corresponding recovery repair. |
10. Fix a rubber bandage on the top end of a core of the valve, or reel up an adhesive tape to exclude a possibility of falling of the valve in the combustion chamber, then block air supply in the cylinder.
11. Check a valve core for existence of signs of wear or mechanical damages. Rotating the valve in the directing plug, estimate the size of a radial side play of its end face defining degree of straightness of a core (the curved valve is subject to replacement).
12. Move the valve up-down in the directing plug, trying to reveal jamming points which existence demonstrates or deformation of a core of the valve, or about damage of the plug - anyway the head is subject to removal for the purpose of performance of necessary recovery repair.
13. Again give air to the cylinder for the purpose of fixing of the valve. Remove a rubber bandage / adhesive tape from a core.
14. Oil a valve core pure motive and establish a new maslootrazhatelny cap.
|
|
Maslootrazhatelny caps of inlet valves are completed with a spring of white color, final - black. |
15. Put on a valve core a valvate spring(s) (an end face with the shortened step of rounds to a head).
|
|
16. Put a plate on a spring, then squeeze a spring(s) by means of the special tool and accurately fill in a landing flute on a valve core crackers of the cutting lock. For temporary fixing of crackers to an otpuskaniye of the tool grease them with dense lubricant from within. |
17. Watching correctness of landing of crackers in a flute, release the device for tightening of a spring.
18. Block air supply in the cylinder and turn out a transitional nozzle from a candle opening.
19. Establish into place assembly of yokes (see the Section Removal, check of a state and installation of assembly of yokes).
20. Establish a cover of a head of cylinders (see the Section Removal and installation of a cover of a head of cylinders).
21. Screw to the place of a spark plug and connect to them (in the required order) wire VV.
22. Start the engine and check it for existence of signs of leak of oil and the unusual noise published by the valvate mechanism. |